Featured Articles

AMD SVP John Byrne named turnaround exec of the year

AMD SVP John Byrne named turnaround exec of the year

Director of AMD’s PR Chris Hook has tweeted and confirmed later in a conversation with Fudzilla that John Byrne, Senior Vice…

More...
Shield Tablet 8 launching on Tuesday July 22nd

Shield Tablet 8 launching on Tuesday July 22nd

We knew the date for a while but as of right now we can confirm that Nvidia’s new Shield Tablet 8,…

More...
AMD confirms 20nm in 2015

AMD confirms 20nm in 2015

Lisa Su, Senior Vice President and Chief Operating Officer, AMD, has confirmed what we told you back in May 2014 – …

More...
AMD reports loss, shares tumble

AMD reports loss, shares tumble

AMD’s debt load is causing huge problems for the chipmaker -- this quarter it had another substantial loss. The tame Apple Press…

More...
AMD A8-7600 Kaveri APU reviewed

AMD A8-7600 Kaveri APU reviewed

Today we'll take a closer look at AMD's A8-7600 APU Kaveri APU, more specifically we'll examine the GPU performance you can…

More...
Frontpage Slideshow | Copyright © 2006-2010 orks, a business unit of Nuevvo Webware Ltd.
Wednesday, 30 April 2008 10:04

MSI X48 is a good step forward - 3 Layout

Written by Eliot Kucharik

Image Image

Review: 4.4GHz and FSB560, but not quite there




Layout:

MSI did a quite nice job, only specification-wise we have some complaints. The board features the new roller-coaster-Northbridge cooler known from the MSI P35 Platinium, the height has increased which successfully blocks some CPU-coolers, such as the Scythe Zipang.


ImageImage

The VRM is an analog dual 4-phase design driven by an ISL6322.  Sadly, MSI didn't opt for a digital VRM solution, but they did a quite good job with the power-consumption in previous products. The CPU EPS V12 connector is located on the right edge of the board above the CPU socket. We had hoped for a location below the CPU-socket to avoid some cable-mess with smaller cases, but it will do.

Image

The memory slots are quite close to the primary PCIe x16 slot, so you need to fiddle with your modules when replacing or upgrading them while a large graphics card is installed, but it's manageable. As usual, the 24-pin power connector is located beneath.


Image

The slots are configured for a quad-crossfire configuration. While "quad-crossfire" may sound "cool," we doubt it's a wise way to go. Three PCIe x16 is the maximum we would recommend and additional PCI slots for older extension cards. The fastest graphics cards come in a two-slot configuration, using two of them, it will render the PCI slot useless. The yellow slots are also only x4 speed, it would have been wiser to have set all slots to x8, because PCIe 2.0 x8 is the same speed as PCIe 1.1 x16. If you own a TV-card or other PCI extension cards, you won't be able to have that and Quad-Crossfire together.

At least the split yellow PCIe x16 slots can be used for other cards beside graphics even though the manual doesn't say anything about it. MSI used an IDT 89HPES16T7ZBH chip to split 8 lanes to 2x 4. Floppy is located on the left edge of the board, which may cause some troubles with big cases.


ImageImage

ImageImage

Network connectivity is provided by one Realtek Gb 8111B PCIe chip and one Intel 82566 PHY, wihich is connected to the ICH9R network MAC. VIA VT6308P chip provides two Firewire-slots, one on the back panel, one header on the board. A Realtek ALC888 chip will give you the onboard sound solution.


Image Image

The SATA and PATA connectors are, as usual, on the bottom edge of the board. Four SATA connectors are angled, so a second large graphics card will fit above them. The SATA 7 and 8 ports are standard and will get in the way with a large two-slot graphics-cards. We don't understand why there are two extra controllers on board, because the Marvell 88SE6111 does feature two SATA-ports but they are not used.

We would have wished for all six ICH9R SATA-ports, the Sil or Marvell would have done nicely for eSATA; what a waste and you have to pay for it. Below left of the PCIe switch-chip, you will find two buttons for power-on and reset, the CMOS-clear-button is located on the back-panel.


ImageImage

Above the yellow PCIe x16 slots you will find an MSI port-80 post diagnostic display, but not a standard LED design, something special. We don't think this was a good idea, because it costs more money and does not provide detailed information only short words such as "CPU", "DRAM", "VGA" and some more. Right of it you will find the super-I/O-controller which contains controllers for PS/2, floppy and fans.


(Page 3 of 6)
Last modified on Monday, 26 May 2008 09:55
blog comments powered by Disqus

 

Facebook activity

Latest Commented Articles

Recent Comments